SGS 1-26B "Little Flyer" series 1.5 meter (60") Laser Cut order Partial Kit with Plans

$129.99
#SN.1799462
SGS 1-26B "Little Flyer" series 1.5 meter (60") Laser Cut order Partial Kit with Plans,

This is a glider model that was developed by a fellow modeler and friend Charlie.

Black/White
  • Eclipse/Grove
  • Chalk/Grove
  • Black/White
  • Magnet Fossil
12
  • 8
  • 8.5
  • 9
  • 9.5
  • 10
  • 10.5
  • 11
  • 11.5
  • 12
  • 12.5
  • 13
Add to cart
Product code: SGS 1-26B "Little Flyer" series 1.5 meter (60") Laser Cut order Partial Kit with Plans

This is a glider model that was developed by a fellow modeler and friend, Charlie Nemake of California in the last 90s which drafted from from his pencil rendered original to offer a fairly simple and straightforward model makers scratch-built or laser cut 1.5 meter intermediate introduction to glider building for display, towline or slope flying. This makes a very scale thermal and slope flyer for light to moderate wind conditions.

Build Log by Pat Tritle here: https://www.rcgroups.com/forums/showthread.php?512936-Building-the-Schweizer-1-26B

Hardware pack listed here on Etsy: https://www.etsy.com/NewPrairieWoodworks/listing/759534208/hardware-kit-for-little-flyer-1-26b?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1602637109899

Purchase price includes:
Plan Sheets, 24x36 inch Rolled, (sheets 1 of 2 and 2 of 2)
Canopy, .030" Clear with protective wrap
Laser Cut Parts Kit:
Sheet 01 1/16" balsa, wing ribs
Sheet 02 1/16" ply, 1/16" fuselage bulkheads, etc.
Sheet 03 1/8" ply, nose skid, servo tray, canopy bows, etc.
Sheet 04 1/8" balsa, horizontal tails
Sheet 05 1/8" balsa, vertical tails

Required to complete model:
Steel Landing Gear Wire, 1/16" x 1" length
Plated Brass Dura-Collars, 1/16", DUB137
Mini Lite Wheel 1-1/2" dia., DUB150MW
Aluminum Wing Rod, .25" OD x 12" length K&S3045
Brass Joiner Sleeve, 9/32" OD x 12" length K&S132
Hinges, Nylon Mini, pkg of 15, DUB119
Pushrods, Sullivan Semi Flexible with Hardware, Set of 2
Bolts, 2-56 x 1/2" with Blind Nut and Washers, DUB125
Bolt, 4-40 x 1-1/4, Nose Block Mount, DUB127
Incidence Pin Hardwood Dowel, 1/8" OD x 4" length
Brass Cup Hooks, 1/2" (2)
Tail Wheel, 1/2" dia. Sullivan 350
Long wood parts if special ordered:
Spars 1/8" x 1/4" x 36" spruce (4), SIGGYS010
Trailing Edge/Aileron 1-1/2" x 5/16" (2), TMRCTE36
Sheeting, 1/16" x 4 x 36" Balsa (4), SIGB143
Leading Edge, 3/8" x 3/8" x 36" Balsa (2) SIGB041
Stringers, order 1/16" x 1/4" x 24" Basswood (8) SIGBA008 (x1-1/3)

.
925 review

4.16 stars based on 925 reviews